Name: In-Drain Heating Cable for Drain Lines Under 2 in (IPHC-DMi)
Brand: YeloDeer
SKU: Y-IW-10
Price: 32.99 USD
Availability: OutOfStock

Overview

Compact In-Drain Heating Cable for Condensate & Small Open Drain Lines

YeloDeer IPHC-DMi is a compact self-regulating in-drain heating cable for freeze protection inside HVAC condensate drains, furnace drains, gray-water discharge lines, and other small non-pressurized drain pipes under 2 in. It is the economical choice for shorter, lighter-duty drain runs up to 75 ft.

Quick Fit Check

Up to 75 ft For shorter condensate and open drain runs.

Under 2 in Pipes Compact cable for smaller condensate and open drain lines.

3W/ft or 5W/ft Select standard or higher output before ordering.

No Integrated GFCI Required ground-fault protection must be provided separately.

No water-pressure rating. This product is not designed to contain or resist internal water pressure. Do not use it in pressurized plumbing, sealed water-supply lines, potable-water pipes, or any pipe that can build pressure.

Choose the Right Drain Heating Cable

Choose This Compact IPHC-DMi For an open condensate or drain line under 2 in and up to 75 ft. Available in 3W/ft or 5W/ft without an integrated GFCI.

Choose Heavy-Duty IPHC-DMa For 2 in and larger sewer or wastewater lines, continuous runs up to 180 ft, integrated GFCI protection, and a thicker cable that is easier to advance through long pipe runs.
Compare the heavy-duty GFCI version →

Need a sealed cable-entry assembly? Choose DrainGuard for a 1/2 or 3/4 in PVC/ABS condensate or low-flow drain. DrainGuard is still not intended for pressurized plumbing.

Automatic Temperature Control

Self-regulating does not mean automatic shutoff. The cable adjusts heat output as temperature changes but remains energized while connected to power. Add the YeloDeer Pipe Heat Tape Thermostat Controller, sold separately, for automatic temperature-based on/off control.

Confirm Before Ordering

Open, non-pressurized condensate or drain application Pipe diameter is under 2 in Required heating length does not exceed 75 ft Accessible open pipe end is available Internal route is clear enough for insertion 3W/ft or 5W/ft output is selected Correct finished length is selected Required ground-fault protection is provided

YeloDeer compact in-pipe heating cable with 3W/ft and 5W/ft options for open drain pipes

Applications

Recommended Applications

YeloDeer compact in-drain heating cable for condensate and small drain pipes

Condensate Drains

HVAC Condensate Furnace Drains Boiler Drains

Small Drain Lines

Gray-Water Discharge Dehumidifier Drains Low-Flow Drains

Cold Problem Areas

Exterior Wall Exits Garages Crawl Spaces

Open Drain Access

Open Pipe Ends Vented Outlets Direct Insertion

Pipe Requirements

Recommended Pipe Size	Drain lines under 2 in, subject to the actual internal opening
Pressure Condition	Non-pressurized only; no water-pressure rating
Required Pipe Layout	Both ends open or vented for normal drainage
Entry Method	Direct insertion through an existing open pipe end
Internal Route	Clear route without blockage, collapse, crushing, or sharp restrictive bends

Select the Right Product

Choose IPHC-DMi For an open condensate or drain line under 2 in and up to 75 ft where separate ground-fault protection is provided.

Choose IPHC-DMa For a 2 in or larger sewer or wastewater line, especially for continuous runs from 76 ft to 180 ft or when a built-in GFCI and heavier cable construction are preferred.

Choose DrainGuard For a 1/2 or 3/4 in PVC/ABS drain that needs a cut-in Y-fitting and sealed cable-entry assembly.

Do Not Use This Product For

Pressurized drinking-water lines or potable-water supply pipes
Closed or sealed pipes that can build pressure
Large sewer or septic pipes better suited to the heavy-duty IPHC-DMa
Blocked, collapsed, crushed, leaking, or unknown internal pipe routes
Routes that require the cable to be forced through sharp elbows or restrictions

Specifications

Technical Specifications

Model	IPHC-DMi
Product Type	Compact self-regulating in-drain heating cable without integrated GFCI
Primary Application	Open condensate drains, furnace drains, gray-water discharge, and small drain lines
Heating Output	3W/ft or 5W/ft at 50°F / 10°C, depending on selected variant
Voltage	120V AC
Cable Type	Self-regulating heating cable
Outer Jacket	Corrosion-resistant fluoropolymer jacket
Cable Size	Approx. 0.31 × 0.19 in / 7.9 × 4.7 mm
Power Cord Length	Approx. 6 ft
Plug Protection	No integrated GFCI; provide required circuit and ground-fault protection
Minimum Bend Radius	1 in at 32°F / 0°C
Maximum Stable Cable Temperature	140°F / 60°C
Recommended Pipe Size	Open drain lines under 2 in
Water-Pressure Rating	None; for non-pressurized drain applications only
Required Pipe Layout	Both ends open or vented for normal drainage
Standard Lengths	5 ft to 75 ft
Custom Lengths	Available by request
Field Cutting	Not allowed

Choose 3W/ft or 5W/ft

3W/ft Standard Output For typical condensate drains, shorter runs, and moderately cold locations with suitable pipe insulation.

5W/ft Higher Output For colder exposure, longer outdoor sections, or drain routes with greater heat loss.

Select the Correct Length

Measure from the open cable-entry point to the farthest freeze-prone section. Include hidden cold-wall and outdoor sections when known. Do not choose a length that requires sharp coiling inside the pipe.

Do not cut, shorten, splice, or modify the heating cable. Select the correct finished length and heating output before ordering.

Installation

Basic Installation Sequence

Confirm the pipe is non-pressurized and both ends remain open or vented for normal drainage.
Shut down related equipment and make the work area safe.
Thaw and clear any existing frozen blockage before inserting the cable.
Measure the route and verify the selected cable length and output.
Insert the cable slowly through the accessible open pipe end.
Stop if it reaches a sharp bend, restriction, blockage, or unknown obstruction.
Keep the power connection outside the pipe and protected from moisture.
Provide grounding, overcurrent protection, and ground-fault protection required for the installation.
Restore normal drainage and confirm the cable does not obstruct flow.

Do Not Force Use gentle hand pressure and stop when resistance increases.

Do Not Cut Standard cables cannot be shortened or spliced in the field.

Protect the Jacket Avoid sharp edges, scraping, crushing, and hard kinks.

Keep Both Ends Open Do not seal this cable into a pipe that can build pressure.

Protect the Circuit This version has no integrated GFCI plug.

Insulate When Suitable Insulation can reduce heat loss from exposed drain sections.

In-drain heating cable for small non-pressurized drain lines

Optional Automatic Control

Connect the cable through the compatible YeloDeer Pipe Heat Tape Thermostat Controller to switch power automatically according to pipe temperature. Keep the total connected load within the controller rating.

FAQ

Does this version include a GFCI plug?

No. IPHC-DMi does not include an integrated GFCI. Provide the grounding, circuit protection, and ground-fault protection required for the installation and applicable electrical requirements.

Is this cable pressure rated?

No. It has no water-pressure rating and is intended only for non-pressurized condensate and drain lines. Do not use it in pressurized plumbing or potable-water supply pipes.

Must both ends of the pipe remain open?

Yes. This original version requires an accessible open entry and an open or vented downstream outlet. For a 1/2 or 3/4 in PVC/ABS drain that must remain closed after installation, compare the DrainGuard kit.

How is DrainGuard different?

DrainGuard includes a 3/4 in Y-fitting, 1/2 in adapters, gasket, sealing grommet, lock nut, and pipe nipples. These parts create a dedicated cable-entry point and help restore a sealed drainage path. It remains limited to non-pressurized, low-pressure drain applications.

What is the difference between 3W/ft and 5W/ft?

The 3W/ft version suits typical condensate and small drain applications. The 5W/ft version provides higher heat output for colder exposure, longer outdoor sections, or greater heat loss.

Can this cable be used for sewer or septic lines?

This compact model is primarily intended for condensate and small open drain lines under 2 in and up to 75 ft. For larger, longer, or more demanding sewer, septic, and wastewater pipes, choose the heavier IPHC-DMa with integrated GFCI and continuous lengths up to 180 ft.

Does the cable turn itself off?

No. Self-regulating cable reduces heat output as temperature rises but remains energized. Use the compatible YeloDeer pipe heat tape thermostat controller for automatic on/off control.

Can it operate in a dry or temporarily empty drain?

Yes, when installed in a suitable non-pressurized open drain route. All electrical, pipe-layout, and installation requirements still apply.

Can I cut the cable to length?

No. Measure the route before ordering and select the correct finished length. Contact YeloDeer for a custom-length project.

Guides

Customer installation of YeloDeer drain heating cable for freeze protection Customer open drain freeze protection installation with YeloDeer heating cable HVAC condensate drain heating cable installation example
Confirm non-pressurized drain conditions Confirm both ends remain open or vented Measure the full freeze-prone route Select 3W/ft or 5W/ft output Identify bends, restrictions, and blockages Plan required electrical and moisture protection

Need selection help? Email yelodeer@yelodeer.com with the drain type, pipe diameter, required heating length, lowest winter temperature, whether the pipe is open or closed, and installation photos.

Menu

In-Drain Heating Cable for Drain Lines Under 2 in (IPHC-DMi)